Re: [PATCH v5 9/9] Documentation: Update VFIO NOIOMMU mode

[Yi Liu <yi.l.liu@intel.com>]

On 5/12/26 02:41, Jacob Pan wrote:
> Document the NOIOMMU mode with newly added cdev support under iommufd.
> 
> Cc: Jonathan Corbet <corbet@lwn.net>
> Signed-off-by: Jacob Pan <jacob.pan@linux.microsoft.com>
> ---
>   Documentation/driver-api/vfio.rst | 46 +++++++++++++++++++++++++++++--
>   1 file changed, 44 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/driver-api/vfio.rst b/Documentation/driver-api/vfio.rst
> index 2a21a42c9386..d97017d80b98 100644
> --- a/Documentation/driver-api/vfio.rst
> +++ b/Documentation/driver-api/vfio.rst
> @@ -275,8 +275,6 @@ in a VFIO group.
>   With CONFIG_VFIO_DEVICE_CDEV=y the user can now acquire a device fd
>   by directly opening a character device /dev/vfio/devices/vfioX where
>   "X" is the number allocated uniquely by VFIO for registered devices.
> -cdev interface does not support noiommu devices, so user should use
> -the legacy group interface if noiommu is wanted.
>   
>   The cdev only works with IOMMUFD.  Both VFIO drivers and applications
>   must adapt to the new cdev security model which requires using
> @@ -370,6 +368,50 @@ IOMMUFD IOAS/HWPT to enable userspace DMA::
>   
>   	/* Other device operations as stated in "VFIO Usage Example" */
>   
> +VFIO NOIOMMU mode
> +-------------------------------------------------------------------------------
> +VFIO also supports a no-IOMMU mode, intended for usages where unsafe DMA can
> +be performed by userspace drivers w/o physical IOMMU protection. This mode
> +is controlled by the parameter:
> +
> +/sys/module/vfio/parameters/enable_unsafe_noiommu_mode
> +
> +Upon enabling this mode, with an assigned device, the user will be presented
> +with a VFIO group and device file, e.g.::
> +
> +  /dev/vfio/
> +  |-- devices
> +  |   `-- noiommu-vfio0	/* VFIO device cdev */
> +  |-- noiommu-0		/* VFIO group */
> +  `-- vfio

how about noiommu-vfioX and noiommu-Y? Just want to deliver the message
that the two number is not 100% identical.

> +The capabilities vary depending on the device programming interface and kernel
> +configuration used. The following table summarizes the differences:
> +
> ++-------------------+---------------------+----------------------+
> +| Feature           | VFIO group          | VFIO device cdev     |
> ++===================+=====================+======================+
> +| VFIO device UAPI  | Yes                 | Yes                  |
> ++-------------------+---------------------+----------------------+
> +| VFIO container    | No                  | No                   |
> ++-------------------+---------------------+----------------------+
> +| IOMMUFD IOAS      | No                  | Yes*                 |
> ++-------------------+---------------------+----------------------+
> +

not quite the above table. Why 'VFIO container' is "No" for VFIO group?

> +Note that the VFIO container case includes IOMMUFD provided VFIO compatibility
> +interfaces when either CONFIG_VFIO_CONTAINER or CONFIG_IOMMUFD_VFIO_CONTAINER is
> +enabled.
> +
> +* IOMMUFD UAPI is available for VFIO device cdev to pin and map user memory with
> +  the ability to retrieve physical addresses for DMA command submission.
> +
> +A new IOMMUFD ioctl IOMMU_IOAS_NOIOMMU_GET_PA is added to retrieve the physical
> +address for a given IOVA. Although there is no physical DMA remapping hardware,
> +IOMMU_IOAS_MAP_FIXED_IOVA is still used to establish IOVA-to-PA mappings in the
> +software page table for later IOMMU_IOAS_NOIOMMU_GET_PA lookups.
> +tools/testing/selftests/vfio/vfio_iommufd_noiommu_test.c provides an example of
> +using this ioctl in no-IOMMU mode.
> +
>   VFIO User API
>   -------------------------------------------------------------------------------
>