From: Jonathan Cameron <jic23@kernel.org>
To: "Nuno Sá" <nuno.sa@analog.com>
Cc: Fan Wu <fanwu01@zju.edu.cn>,
David Lechner <dlechner@baylibre.com>,
Andy Shevchenko <andy@kernel.org>,
linux-iio@vger.kernel.org, linux-kernel@vger.kernel.org,
stable@vger.kernel.org, Song Li <songl@zju.edu.cn>
Subject: Re: [PATCH] iio: adc: ad_sigma_delta: fix use-after-free on unbind
Date: Sun, 27 Sep 2026 20:09:05 +0100 [thread overview]
Message-ID: <20260927200905.1cebc335@jic23-hlaptop> (raw)
In-Reply-To: <arTioh-Dax9Ogizj@nsa>
On Thu, 24 Sep 2026 09:45:07 +0100
Nuno Sá <nuno.sa@analog.com> wrote:
> On Wed, Sep 23, 2026 at 09:48:07AM +0000, Fan Wu wrote:
> > ad_sd_buffer_postenable() allocates sigma_delta->samples_buf with
> > devm_krealloc() at runtime, so its devres entry sits after all
> > probe-time entries of the driver. devm resources are released in
> > reverse allocation order, which means unbind frees samples_buf before
> > iio_device_unregister() disables the buffers and detaches the trigger
> > pollfunc. The data ready IRQ is still enabled at that point, so
> > ad_sd_trigger_handler() can still run and memcpy() incoming samples
> > into the freed samples_buf.
> >
> > Fix this by preallocating the buffer in
> > devm_ad_sd_setup_buffer_and_trigger(), before the triggered buffer and
> > the IRQ are set up, so it is freed only after iio_device_unregister()
> > has drained the trigger handler via free_irq(). Size it for the worst
> > case of all sequencer slots being active; ad_sd_validate_scan_mask()
> > already caps the number of active channels at num_slots.
> >
> > This issue was found by an in-house static analysis tool.
> >
> > Fixes: 8bea9af887de ("iio: adc: ad_sigma_delta: Add sequencer support")
> > Cc: stable@vger.kernel.org
> > Co-developed-by: Song Li <songl@zju.edu.cn>
> > Signed-off-by: Song Li <songl@zju.edu.cn>
> > Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
> > ---
>
> Makes sense to me! One minor nit Jonathan might be ale to tweak when
> applying. With that:
Applied to the fixes-togreg branch of iio.git and tweaked as suggested.
Thanks,
Jonathan
>
> Reviewed-by: Nuno Sá <nuno.sa@analog.com>
>
> > drivers/iio/adc/ad_sigma_delta.c | 32 +++++++++++++++++++-------------
> > 1 file changed, 19 insertions(+), 13 deletions(-)
> >
> > diff --git a/drivers/iio/adc/ad_sigma_delta.c b/drivers/iio/adc/ad_sigma_delta.c
> > index 1b41029..4f982c6 100644
> > --- a/drivers/iio/adc/ad_sigma_delta.c
> > +++ b/drivers/iio/adc/ad_sigma_delta.c
> > @@ -498,7 +498,6 @@ static int ad_sd_buffer_postenable(struct iio_dev *indio_dev)
> > const struct iio_scan_type *scan_type = &indio_dev->channels[0].scan_type;
> > struct spi_transfer *xfer = sigma_delta->sample_xfer;
> > unsigned int i, slot, channel;
> > - u8 *samples_buf;
> > int ret;
> >
> > if (sigma_delta->num_slots == 1) {
> > @@ -530,7 +529,7 @@ static int ad_sd_buffer_postenable(struct iio_dev *indio_dev)
> > xfer[1].bits_per_word = scan_type->realbits;
> > xfer[1].len = spi_bpw_to_bytes(scan_type->realbits);
> > } else {
> > - unsigned int samples_buf_size, scan_size;
> > + unsigned int scan_size;
> >
> > if (sigma_delta->active_slots > 1) {
> > ret = ad_sigma_delta_append_status(sigma_delta, true);
> > @@ -538,17 +537,6 @@ static int ad_sd_buffer_postenable(struct iio_dev *indio_dev)
> > return ret;
> > }
> >
> > - samples_buf_size =
> > - ALIGN(slot * BITS_TO_BYTES(scan_type->storagebits),
> > - sizeof(s64));
> > - samples_buf_size += sizeof(s64);
> > - samples_buf = devm_krealloc(&sigma_delta->spi->dev,
> > - sigma_delta->samples_buf,
> > - samples_buf_size, GFP_KERNEL);
> > - if (!samples_buf)
> > - return -ENOMEM;
> > -
> > - sigma_delta->samples_buf = samples_buf;
> > scan_size = BITS_TO_BYTES(scan_type->realbits + scan_type->shift);
> > /* For 24-bit data, there is an extra byte of padding. */
> > xfer[1].rx_buf = &sigma_delta->rx_buf[scan_size == 3 ? 1 : 0];
> > @@ -855,6 +843,24 @@ int devm_ad_sd_setup_buffer_and_trigger(struct device *dev, struct iio_dev *indi
> >
> > indio_dev->setup_ops = &ad_sd_buffer_setup_ops;
> > } else {
> > + const struct iio_scan_type *scan_type =
> > + &indio_dev->channels[0].scan_type;
> > + unsigned int samples_buf_size;
> > +
> > + /*
> > + * Worst-case size: all sequencer slots can be active, capped
> > + * at num_slots by ad_sd_validate_scan_mask().
> > + */
> > + samples_buf_size =
> > + ALIGN(sigma_delta->num_slots *
> > + BITS_TO_BYTES(scan_type->storagebits),
> > + sizeof(s64));
> > + samples_buf_size += sizeof(s64);
> > + sigma_delta->samples_buf =
> > + devm_kzalloc(dev, samples_buf_size, GFP_KERNEL);
>
> Why the line break for devm_kzalloc(). Keep it in the same line please.
> Tbh same for for the ALIGN() call but at least that one is coherent with
> the original code.
>
> - Nuno Sá
>
> > + if (!sigma_delta->samples_buf)
> > + return -ENOMEM;
> > +
> > ret = devm_iio_triggered_buffer_setup(dev, indio_dev,
> > &iio_pollfunc_store_time,
> > &ad_sd_trigger_handler,
> >
prev parent reply other threads:[~2026-09-27 19:09 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-09-23 9:48 Fan Wu
2026-09-24 8:45 ` Nuno Sá
2026-09-27 19:09 ` Jonathan Cameron [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260927200905.1cebc335@jic23-hlaptop \
--to=jic23@kernel.org \
--cc=andy@kernel.org \
--cc=dlechner@baylibre.com \
--cc=fanwu01@zju.edu.cn \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nuno.sa@analog.com \
--cc=songl@zju.edu.cn \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®