RE: [EXT] Re: [PATCH v5 00/22] wifi: nxpwifi: create nxpwifi to support iw61x

[Jeff Chen <jeff.chen_1@nxp.com>]

Hi Martyn,

Thanks again for your detailed feedback and testing.

From what you've described, this issue doesn't appear to be caused by the
nxpwifi driver itself. The Wi-Fi side seems to be functioning correctly.

To simplify things and avoid firmware loading conflicts, I recommend using
the Wi-Fi-only firmware with the nxpwifi driver, and letting the btnxpuart
driver handle its own Bluetooth firmware loading.
Also, I've looped in Neeraj and Amit, who are the maintainer of the btnxpuart
driver.

From your BT-only scenario logs:
We can confirm that the host-to-chip communication is working correctly, and the
firmware download completes successfully. This rules out hardware issues and 
confirms that the UART link is functional. The problem seems to occur during HCI initialization, 
where the btnxpuart driver reports repeated Frame reassembly failed (-84) errors.

We suggest that to debug this quickly, it would be very helpful if you could capture the UART 
lines (TX/RX/CTS/RTS) using a logic analyzer (e.g., Saleae) and share the trace. This would allow
us to inspect what's happening on the wire and identify the root cause of the 
"Frame Reassembly Failed" error. There are affordable logic analyzers compatible with Saleae
software, such as:
https://www.amazon.in/Robodo-Electronics-USBLA24M-Analyser-Compatible/dp/B07B8KHYDD?source=ps-sl-shoppingads-lpcontext&ref_=fplfs&psc=1&smid=AJ6SIZC8YQDZX

best regards,

Jeff
> -----Original Message-----
> From: Martyn Welch <martyn.welch@collabora.com>
> Sent: Saturday, October 11, 2025 12:22 AM
> 
> On 09/10/2025 17:01, Jeff Chen wrote:
> > On Tue, Oct 07, 2025 at 05:49:59 PM +0100, Martyn Welch wrote:
> >> This seems to be working well for me, at least for Wifi. I'd like to
> >> get Bluetooth up as well. The bluetooth driver (btnxpuart) doesn't
> >> seem happy loading the bluetooh firmware:
> >
> 
> Yes, I'm currently using the wifi only firmware. If I'm not mistaken, that's the
> only firmware that the NXPWifi driver will currently use. It appears that it
> should be able to load `firmware_sdiouart`, but that doesn't appear to be set
> anywhere and thus it's not considered. I tried to rename the combo firmware
> to have the name used for the wifi only firmware, but that was failing for me
> (more about that in a moment).
> 
> > To help us reproduce and investigate further, could you please share:
> > - Your test platform (SoC, board, etc.)
> 
> Custom board based on Renesas RZ-G2L, using Ezurio Sona NX611 M.2 1216
> module.
> 
> Kernel is 6.17 with an added custom DT, a few patches for other hardware and
> the NXPWifi patch series.
> 
> Both btnxpuart and nxpwifi are built as modules.
> 
> The firmware itself is what Ezurio provide in their Yocto layer:
> 
> $ md5sum *
> 6a9307d27c3bdb3bde800265056ab217  sd_w61x_v1.bin.se
> 8a28ec7f1b77dbde0ac7568d0426c669  sduart_nw61x_v1.bin.se
> d38935f03dbe6da7a9ac3daf58e640bf  uartspi_n61x_v1.bin.se
> 
> 
> Looking a bit deeper, if I try and load the combined firmware, the bluetooth
> modules attempts to load before the WiFi driver has had a chance to complete
> loading the firmware which is resulting in the firmware failing.
> 
> If I blacklist the btnxpuart module (and rename the combo firmware), it loads:
> 
> > - Your test steps
> 
> At the moment, booting and checking to see if the hardware has probed.
> If it has, ensure I can connect to my wifi network and ensure that I can pass a
> little bit of traffic.
> 
> > - The exact firmware version you're using
> 
> As above.
> 
> > Also, have you tried running Bluetooth in a BT-only scenario (without
> > loading the Wi-Fi driver)? Does that work correctly?
> >
> 
> I hadn't. Just gave that a go and I seem to be getting the same failure (though :
> 
> $ sudo dmesg | grep hci0
> [   40.859055] Bluetooth: hci0: ChipID: 7601, Version: 0
> [   40.889487] Bluetooth: hci0: Request Firmware:
> nxp/uartspi_n61x_v1.bin.se
> [   42.850682] Bluetooth: hci0: FW Download Complete: 396444 bytes
> [   42.850736] Bluetooth: hci0: Frame reassembly failed (-84)
> [   44.222243] Bluetooth: hci0: Frame reassembly failed (-84)
> [   44.230226] Bluetooth: hci0: Frame reassembly failed (-84)
> [   44.237480] Bluetooth: hci0: Frame reassembly failed (-84)
> [   44.247567] Bluetooth: hci0: Frame reassembly failed (-84)
> [   44.254188] Bluetooth: hci0: Frame reassembly failed (-84)
> [   44.263459] Bluetooth: hci0: Frame reassembly failed (-84)
> [   44.269814] Bluetooth: hci0: Frame reassembly failed (-84)
> [   46.280494] Bluetooth: hci0: Opcode 0x1002 failed: -110
> [   46.285835] Bluetooth: hci0: command 0x1002 tx timeout
> 

> Are there any BT patches that I'm missing?
> 
> Martyn
> 
> > Thanks,
> > Jeff